Civil Structure Engineering
Sharing knowledge about civil engineering projects
Home
Submenu item 1
Submenu item 2
Submenu item 3
Submenu item 4
About
Services
Submenu item 1
Submenu item 2
Submenu item 3
Submenu item 4
Portfolio
Testimonials
Contact
Error 404
skip to main
|
skip to sidebar
LINK
Kawat Bronjong Penahan Longsor
Tas Kulit Pria Wanita
Grosir Sandal Murah
Gelang Tasbih Kayu Kokka
Jasa Perencanaan Konstruksi Bangunan
Pages
Home
About Me
Riza Exe
View my complete profile
Followers
Powered by
Blogger
.
Blog Archive
▼
2011
(25)
▼
September
(25)
Loadbearing Architectural Precast Concrete Wall Pa...
Concrete Shear Wall Construction
Wind and Bridge Failures
Road Drainage Systems
Stabilizing Ground by Geotextile
The purpose of shaft grouting of deep foundations?
Should vehicular parapets be designed to be strong?
The purpose of road studs in roads?
What are the advantages of using rockfill over ear...
What is shock transmission unit in bridges?
Sometimes the side of concrete bridges is observed...
Are there any problems associated with Integral Ab...
What are the advantages of cable-stayed bridges ov...
How does flatter affect the stability of long brid...
Load And Resistance Factor Design For Building Column
Allowable Stress Design For Building Beams
Load And Resistance Factor Design For Building Beams
Allowable Stress Design For Shear in Buildings
Stresses In Thin Shells
Bearing Plates
Column Base Plates
Plate Girder In Buildings
Deflections of Bents and Shear Walls
Design of Stiffeners Under Loads
Composite Construction
Loadbearing Architectural Precast Concrete Wall Panels
Riza Exe
1
Building
9:17 PM
Read more »
Concrete Shear Wall Construction
Riza Exe
0
Building
9:43 AM
News
News
Entri Populer
Allowable Stress Design For Shear in Buildings
The AISC specification for ASD specifies the following allowable shear stresses F v , ksi ( ksiX6.894=MPa) When the shear in the web exc...
Deflections of Bents and Shear Walls
Horizontal deflections in the planes of bents and shear walls can be computed on the assumption that they act as cantilevers. Deflections ...
Allowable Stress Design For Building Beams
The maximum fiber stress in bending for laterally supported beams and girders is F b = 0.66F y if they are compact, except for hybrid gi...
Road Drainage Systems
In roadwork, the main drainage requirements fall into two categories. 1. Sub-soil Drainage There must be a provision of sub-soil drainage...
Are there any problems associated with Integral Abutment Bridge?
Integral Abutment Bridges are bridges without expansion joints in bridge deck. The superstructure is cast integrally with their superstru...
Stresses In Thin Shells
Results of membrane and bending theories are expressed in terms of unit forces and unit moments, acting per unit of length over the thic...
How does flatter affect the stability of long bridges?
Flutter is a potentially destructive vibration and it is self-feeding in nature. The aerodynamic forces on a bridge, which is in nearly sa...
Load And Resistance Factor Design For Building Beams
For a compact section bent about the major axis, the unbraced length L b of the compression flange, where plastic hinges may form at failu...
The purpose of shaft grouting of deep foundations?
In shaft grouting operation, tube-a-manchette pipes are fixed at regular spacing to the reinforcement cage. After concreting barrettes/bore...
Load And Resistance Factor Design For Building Column
Plastic analysis of prismatic compression members in buildings is permitted if (F y ) ½ (l/r) does not exceed 800 and F u less than e...
News2